Whitsunday White Limewash Paint (4L)

Dalray Limewash is a breathable mineral coating made from hydrated lime and mineral pigments. It creates a soft, matte finish with gentle tonal movement and can be used on a wide range of surfaces including interior painted walls, brick, render, masonry and plaster.

Unlike acrylic paints and many modern limewash-style coatings, Dalray Limewash contains no added VOCs, plastics or acrylic binders, allowing it to form a natural mineral bond with absorbent surfaces.

The appearance of our limewash paint may vary depending on the surface, lighting, and primer used. Like all authentic limewash finishes, light surface transfer when touched is a natural characteristic of the mineral finish, particularly in the first few weeks while curing. This is part of what gives limewash its living, breathable quality and reduces over time. Using Dalray Limewash Primer can help reduce surface transfer. In higher-use interior areas, Dalray Acrylic Sealer may be applied for additional durability and easier maintenance, noting that it will reduce the breathability of the limewash.

Suitable for interior and exterior brick, masonry, stone, render, plaster and most previously painted walls with a matte or low-sheen finish where the surface remains porous.

Limewash is not recommended for floors or wet zones such as inside showers. It may be used on general bathroom and laundry walls outside direct splash zones where there is adequate ventilation. In regularly humid areas, use a compatible breathable mineral sealer. Dalray Acrylic Sealer may be suitable for well-ventilated bathrooms or powder rooms where humidity is limited.

Format: Powdered mineral limewash paint

Pack size: 1.6kg; makes approximately 4L when mixed

Water: 3L per full 1.6kg bag

Coverage: Approximately 30m² with two coats on smooth, properly primed interior walls. Coverage is lower on rough or porous brick and render.

Application: Block brush; apply at least two thin coats

Use: Suitable prepared interior walls and exterior masonry. Not for floors or shower wet zones.

The surface must be clean, dry and free from dust, oils or loose material. Repair cracks if required and ensure the surface is sound and suitably absorbent. Glossy or fully sealed surfaces should be dulled, sanded or primed before application.

Testing on a small area is recommended before full application.

A primer is not required on raw, absorbent mineral surfaces such as brick or render. Limewash can be applied over suitable water-based undercoats in many situations. However, for best and most consistent results across all substrates, we recommend using the Dalray Limewash Primer, which helps regulate suction, improve mineral bonding, and reduce rub-off. On new or unpainted plasterboard (gyprock), apply two coats of water-based acrylic undercoat first. On very dark colours, apply one to two coats of water-based acrylic undercoat. Then follow with the Dalray Limewash Primer.

In higher-use interior areas such as hallways, entryways, well-ventilated powder rooms and commercial spaces, Dalray Acrylic Sealer can be applied to improve durability, reduce surface transfer and marking, and make the finish easier to maintain. As an acrylic coating, it reduces the breathability of the limewash and is not suitable for exterior surfaces or areas exposed to direct, standing or pooling water.

In bathrooms or other areas subject to regular humidity and moisture, we recommend using a compatible breathable mineral sealer instead. Dalray Acrylic Sealer may be suitable in well-ventilated bathrooms or powder rooms where humidity is limited and the surface is outside direct splash zones.

For exterior surfaces, use a compatible breathable mineral sealer designed for outdoor exposure.

Any sealer may slightly deepen the colour or alter the finish, so we recommend testing it on a small, inconspicuous area first.

For a full 1.6kg bag, add 3L of hot tap water (approximately 50°C) to a bucket, then add the limewash powder gradually. Mix thoroughly for approximately 3 minutes until smooth. Do not use boiling water. Stir during use.

Apply thin coats with a block brush in criss-cross strokes. Apply at least two coats, allowing approximately 3–4 hours between coats under suitable conditions. Follow the application guide for surface preparation and technique.

A third coat is optional for additional texture. Use relaxed criss-cross strokes or a soft cloud-like motion to build natural depth and variation. Using less paint on the brush will generally produce a more textured finish.

We offer free shipping Australia-wide on orders over $59.95. Orders are dispatched within 1–3 business days. Tracking information is provided once your order is shipped.

This product is made primarily from hydrated lime sourced from limestone and combined with mineral pigments. Mineral additives are also added to improve workability and binding. No plastics or synthetic resins are added.

Limewash creates a soft, breathable mineral finish rather than a sealed paint film. The final result will vary depending on factors such as surface type, preparation, dilution, application technique and curing conditions.

As with all decorative finishes, proper surface preparation and application are essential to achieving the best result.

When mixing and applying, use appropriate protective equipment including a mask and gloves, and ensure adequate ventilation. Avoid inhaling lime dust and keep out of reach of children. To the extent permitted by law, Dalray’s liability is limited to replacement of the product or refund of the purchase price. See our terms and conditions and safety data for more details.